Live View
from Taiwan
12-14 hours ahead of
North America
(UserID: Guest, no password)
|
Geovision Accessories for PTZ and Alarm
Geovision Accessories for PTZ and Alarm is a set of three units: GV-net, GV I/0 and GV Relay. You can also use wall mounted "Digital i/o". The complete set works together with Geovision cards (GV250, GV600, GV650, GV750, GV800, GV1120, GV1240, GV1480), alarm relay control and PTZ camera to provide function as:
- Start recording from any camera once relay contact status is changed.
- Initiate modem, network and/or pager calls once relay contact status is changed.
- Change relay contact status once there is motion detected from cameras connected to the Geovision card. (e.g. Lock up doors, windows, start off alarms.)
- Control PTZ (Pan Tilt Zoom) cameras (up to 16) for pan, tilt zoom function over the web browser.
- Use RS232 computer com port to control input ouput relays.
| GV-NET Card & GV-NET/IO card |
GV-NET Card
GV-NET I/O Card |
GV-NET Card converts RS232 (serial, comm port) to RS485 and can be installed inside a PC.
The GV-NET/IO card is a GV-net card with 4 inputs and 4 relay outputs
|
| Specification |
| RS-232 to PC |
RJ11 to DB9 female cable |
| RS-485 + |
Connect to GV-IO / PT-811M RS-485+ or Pelco, Ademco, Lilin Dome camera RS-485+
|
| RS-485 - |
Connect to GV-IO / PT-811M RS-485 -orPelco, Ademco, Lilin Dome camera RS-485 -
|
| Input |
| Input | 4 |
| Input Signal | 0~5 V DC (floating)/TTL |
| High State | 5V |
| Low State | 0V |
|
| Output |
| Relay Output | 4 |
| Relay Status | Normal Open |
| Relay Capacitance | 1A/30V DC; 0.3A/125V (230V)AC |
| Relay ON Time | 4ms |
| Relay Off Time | 4ms |
|
| Communication |
RS485, 4,800 ~ 9,600 bps |
| DC 5V, 1A |
DC5V, 1A |
Enviromental
Condition |
| Operation Temperature | 0 to 50 degree C
|
| Humidity | 5% to 95% (non-condensing) |
|
| Installation Guide |
GV-NET Card
GV-NET/IO Card (125V)
|
| GV-IO 12-In Card |
 |
The GV-IO with 12-point digital inputs provides an interface for your external devices such as sensors and detectors.
|
| Specifications |
|---|
| Input |
Input | 12 |
Input Signal | 5V DC (floating) / TTL |
High State | 5V |
Low State | 0V |
| Operating Temperature | 0~50 degree C |
| Humidity | 5%~95% (non-condensing) |
| Hardware Required | GV-NET/IO Card |
| Compatible Model | GV-600V3, GV-650V3, GV-800V3, GV-1000 V1.21 |
| Dimensions | 64mm x 99mm |
| Installation Guide | GV-IO 12-In Card |
| GV-IO 12-Out Card |
 |
GV-IO card with 12-point relay outputs provides an interface to your external devices such as alarms and gates.
|
| Specifications |
|---|
| Output |
Relay Output | 12 |
Relay Status | Normal Open |
Relay Capacitance | 2A / 30V DC; 0.25A / 250AC |
Relay ON Time | 4ms |
| DC IN | DC 5V, 1A |
| Operating Temperature | 0~50 degree C |
| Humidity | 5%~95% (non condensing) | \
| Hardware Required | GV-NET/IO card |
| Compatible Model | GV-6003V, GV-6503V, GV-8003V, GV-900, GV-1000V1.21 |
| Dimensions | 107 mm x 99mm |
| Installation Guide | GV-IO 12-Out Card |
| GV-Net RS-232/RS485 Converter |
 |
GV-Net is a device that converts RS232 to RS 485. To be connected to COM1 or COM2 of your computer.
|
| Specification |
| RS-232 to PC |
RS-232 to PC 9-pin male-female cable |
| RS-485+ |
Connect to GV-I/O / PT-811 RS-485+ or Pelco, Ademco, Lilin Dome camera RS-485+
|
| RS-485- |
Connect to GV-i/O / PT-811 RS-485- or Pelco, Ademco, Lilin Dome camera RS-485-
|
| DC IN |
Power Adaptor DC 5V, 1A Inner Positive |
| Communication |
RS-485, 1,200~19,200 bps |
| Opetation Temperature |
0~50 degree C |
| Humidity |
5%~95% (non-condensing) |
| Dimensions |
103 (W) x 32 (H) x 64 (D) mm |
| GV Com |
|
Specifications |
| Serial Interface |
RS-232 |
Signal: DCD, RxD, TxD, DTR, GND, DSR, RTS, CTS |
| Connecter: DB9 Male |
| RS-485 |
Signal: D+, D |
| Connector: Terminal Block |
| 16 KV ESD for All Signals |
Serial Line Protection |
| USB |
Compliance | USB 1.1, 1.0 |
| USB 2.0 Backward Compatible |
| Speed | Full Speed 12 Mbps |
| Communication Parameters |
Parity | None, Even, Odd |
| Data Bit | 7,8 |
| Stop Bit | 1(default), 2 |
| Flow Control | RTS/CTS, XON/XOFF |
| Speed | 600 bps to 115,200 bps |
| Enviromental Conditions |
Operation Temperature | 0°C~55°C |
| Humidity | 5%~95% (Non-Condensing) |
| Dimensions |
103(w) x 32(H) x 64(D)mm
|
| GV-Hub |
 |
The GV-Hub adds 4 RS-232 and RS-485 serial ports to your PC's USB port. The USB solutions for serial ports extension is perfect for mobile insturmentation and POS appalications.
|
| Specification |
|---|
| Serial Interface |
| RS-232 |
Signal: | DCD, RxD, TxD, DTR, GND, DSR, RTS, CTS |
Connector: | 4 x DB9 Male (A, B, C, D) |
| RS-485 |
Signal: | D+, D-, GND |
Connector: | 4 x Terminal Block (A, B, C, D)
| | Serial Line Production | 16 KV ESD for All Signals |
| USB |
Compliance | USB 1.1, 1.0
USB 2.0 Backward Compatible |
Speed | Full Speed 12 Mbps |
| Communication |
Parity | None, Even, Odd |
Data Bit | 7,8 |
Stop Bit | 1,2 |
Flow Control | RTS/CTS,XON/XOFF |
Speed | 600 bps to 115,200 bps |
| Environmental Conditions |
Operation Temperature | 0~55 Degree °C |
Humidity | 5%~95% (non-condensing) |
| Dimensions | 103 (W) x 30 (H) x 125 (D) mm |
| Installation Guide | GV-Hub |
| GV-Loop Through Card |
 |
The GV-Loop Through Card is design to take the video signal directly from the GV Capture Card, without internal device processes, and the split int 16 singals while maintaining video quality.
|
| Specification |
|---|
| Interface | 2 x 40-pin connector |
| Output Interface |
2 x 15-pin D-type ports |
1 x 40-pin connector |
| Input Signals | 16 channels |
| Dimensions | 130 (W) x 98 (H) mm |
| Installation Guide | GV-Loop Through Card |
| GV-IO |
 |
GV-IO is a 8 point digital input and 16 point digital output controller. The dry relay contacts provide an interface to your external devices such as sensors or detectors.
|
| Specification |
| Input |
8 |
| Input Signal |
0-5 V DC (floating) |
| Lo/ High State |
0V-5V |
| Wiring Label |
GND, DI 1~DI 8 |
| Output |
16 |
| Output Circuit |
TTL Open Collect |
| Wiring Label |
(+5V-1, DO 1-1 ~ DO 8-1) or (+5V-2, DO1-2 ~ DO 8-2) |
| DC In |
Power Adapter DC 5V, 2A Inner Positive |
| RS-485+ |
Connect to GV-NET RS-485+ |
| RS-485- |
Connect to GV-NET RS-485- |
| Communication |
RS485, 9600 bps |
| Dimension |
202(W) x 166(H) x 39(D) mm |
| Operation Temperature |
0 to 50 degree C |
| Humidity |
5% to 95% (non-condensing) |
| GV-Relay |
 |
GV-Relay is a relay output module with 8 points relay output interface. This device is to actually control your alarm or PTZ cameras and connects to the control source of GV-IO output.
|
| Specification |
| Relay Output |
RL1~RL8 |
Relay Control
Source |
+5V, DO1~DO8 connect Output of GV-IO
|
| Relay Status |
Normal Open
|
| Power Consumption |
12VDC, 350mA(MAX) |
| Relay capacitance |
P6A / 250V AC; 10A / 125V AC; 5A / 28V DC |
| Relay On Time |
8 ms |
| Relay Off Time |
5 ms |
| Dimension |
202(W) x 166(H) x 39(D) mm |
| Digital i/o module |
|
Digital i/o module combines GV-i/o and GV-relay into one wall mount unit. This device is works with computer "com port" RS232, can work independently or with GeoVision software to provide 8 input and 8 output alarm and relay control. This module can be expanded to handle 16 input and 8 output, or 8 input and 16 output.
This module works with GeoVision software to control pan tilt zoom camera using the 8 relay output.
This digital i-o can be used to work with any other types of remote sensing control, computer controlled machinery, robotics, industrial automation and feedback systems. SDK is available free. |
| Specification |
| Communication format |
RS232, ModBus/RTU protocol |
| Input control |
1 ~ 8, optional 9 ~ 16 |
| Input control signal |
0V - 5V floating |
| Input Wiring Label |
Ground, DI1 ~ DI8, optional DI9 ~ DI16 |
| Relay Output |
RL1 ~ RL8, optional RL9 ~ RL16 |
| Relay Status |
Normal Open
|
| Relay Type |
Single throw double pole
|
| Relay current handling capacity |
10A |
| Dimension |
218(W) x 305(H) x 39(D) mm |
|
